![]() ![]() If this does not happen, then you likely have some amount of sediment or grime that is affecting your earbud’s ability to fully connect to their case. ![]() To start you will want to very delicately press against the trio of charging extensions to see if they are cooperative to the touch and pop back quickly. What you will want to do is grab a toothpick and non-abrasive cloth, towel, or dry wipe for the cleaning process. While this can also mean that the charging case itself might be damaged, the simplest fix is taking a bit of elbow grease to the product. If you have put your earbuds into their case and noticed that one of the charging indicator LEDs has not lit up then the problem is more than likely an obstruction in your charging case. If this hasn’t resolved the dead earbud then continue reading for further fixes. This solution is going to be the typical fix for this issue and should you encounter it again you can follow the same steps to fix the problem. You will need to form a fresh pairing with your smart device, once it is connected check to see if your earbud problem has been resolved.The middle light in the charging case will blink an alternating blue and white to inform you it is in pairing mode.Your earbud will power off, place it back into the charging case.Now tap the touch button twice and hold it down for five seconds on the opposite side of the earbud.There is a sensor found on the inner part of the earbud, put your finger over it or place it into your ear to cover the sensor.Like most JBL wireless earbuds, start by unpairing the earbuds from your connected device and removing the right earbud from its charging port.Pair the headphones with a device of your choosing to check if the quiet earbud is working correctly.For certain models, wait until a blue and white light begins to flash, indicating the reset has completed.Hold down the singular button on the back for no less than five seconds.Remove the earbuds from their charging case.Delete or remove the earbuds from their connected device.Test to make sure both earbuds are working correctly.Your earbuds have been reset, you can now re-pair them with your device of choice.Clear any pairing information on your phone that has to do with the earbuds.Grabbing only the right earbud, hold down the button for no less than ten seconds. ![]() Place the two earbuds back into their charging ports.Plug the charging case into a working power source.Remove the JBL Tune earbuds from your connected devices.Connect them to your preferred device and see if the quiet or non-responsive earbud is working.If done as instructed, the earbuds will be blinking blue.Hold the button on both earbuds until they boot up.Both earbuds will shut off which will be signified by the LED powering off.With the earbud still in your hand, tap the button three times, holding it down on the third tap for no less than five seconds.Take out both earbuds from their charging case and put one down, it doesn’t matter which.If you cannot see this light on one of the earbuds then your problem stems from more than just a glitchy BlueTooth connection and we will alleviate the problem further below. You can determine this from most JBL products by a charging light that will emit from the earbuds. ![]() This is an easy process that will take little more than five minutes at the maximum and the steps are simple to follow.īefore resetting your Bluetooth, double-check that both earbuds are completely charged to ensure that you don’t misdiagnose the issue. If you are experiencing issues with a quieter or completely silent earbud, chances are the easiest fix is going to be resetting the Bluetooth connection. For the sake of saving you time, there is no point attempting multiple fixes when the problem is that you are outside of your coverage area. Further down you will find fixes for individual products that have issues that are unique to their model.Ĭheck to make sure you are within Bluetooth range before attempting these solutions. Regardless of which JBL product you are having issues with, these solutions are designed to fit a wide range of products and can be utilized to fix the issues you are having with your earbuds. To ensure that you have headphones that emit music from both sides, let’s take an extensive look at all the different reasons why your earbuds are not working on one side. While some people might be able to ignore this problem and soldier on with one headphone, the majority of consumers don’t want a product that only half works. Despite the positive reviews most JBL earbuds get, they are not immune to this common headache. The reoccurring issue of a dead or non-responsive earbud is a problem that has plagued folks since the inception of headphones. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |